Following are changes and new features not described in the manual.

INSTALLATION

You may now type an optional source diskette drive letter when installing
to a hard disk.  If you specify only the hard disk drive, A: is still
assumed as the source diskette.  Also, the hard disk may now be either
C:, D:, or E:.	For, to install from diskette B: to hard disk E:, type:

	b:
	install  b:  e:

To install from diskette A: to hard disk C:, type:

	a:
	install  c:

DISPLAY DRIVERS

Additional display adaptor types such as VGA or EGA-MONO are now supported.
Choose VGA-MONO or EGA-MONO if you have a monochrome monitor attached to
your VGA or EGA display adaptor.  Choose VGA-PROF if you have a Paradise
Professional VGA board attached to a multisync color monitor.

A new /f startup switch may be used when the VGA driver has been chosen and
you have a multisync type monitor.  It increases the vertical size of the
display.  If your display is compressed, try typing "SC /F" when you start
Spectra Calc.

TEXT EDITOR

The Spectra Calc Editor now supports text searching.  When using the Editor
(either from Text, Arithmetic Edit, or from within Search), you may press
Alt-F5 or Ctrl-F to find the next occurrence of a text string after the cursor.
A "Find:" prompt appears.  Type the character or characters to be found and
then press Enter.  The cursor moves to the next occurrence of the typed
characters in your file.  Press Alt-F6 or Ctrl-N to find another occurrence
of the same text string.  Upper and lower case letters match each other.

ARITHMETIC

The TfromA, AfromT, and KfromT selections on the Arithmetic Other menu have
been removed.  However, equivalent operations are performed by the Trans,
Absorb, and KMunk selections on the Arithmetic menu.  These automatically do
a conversion if the current file is the appropriate type (absorbance for Trans
or transmission for Absorb or KMunk).  Otherwise, they automatically ratio
with the current Reference file and then produce the selected type.  Also, the
new Curvefit choice in the Arithmetic Other menu starts the CURVEFIT program.
Finally, the Arithmetic Other XShift choice directly calls the SHIFT program.

AVERAGE is a new Arithmetic Application which allows two or more spectra to
be co-added into a single averaged spectrum.  You may choose to average
sequentially-numbered spectra on the disk such as NAME1, NAME2, NAME3, etc.
If so, you simply point to the first file in the sequence on the disk and
averaging stops when the next sequentially named file cannot be found.	You
may also choose each file individually from the disk, one at a time.  You must
then type a file name of up to eight letters for the average spectrum and
choose whether it should be saved to disk in addition to being left in memory.

BEEPOFF is a new Arithmetic Application which allows the error beep to be
turned off or back on.

BKMNDU70.AB is an Array Basic program to import ASCII data files created by
a Beckman DU 70.  The progam expects a *.BEC extension.  Unlike most file
import converters, the DU70 converter is an Array Basic program and is started
by selecting F2/Arithmetic/DoProgram and typing "BKMNDU70" followed by return.

BUILDLIB (for Spectra Calc Search and Works only) is a new Arithmetic
Application which will build a library from all .SPC files listed in a
directory or from an ASCII text file (created with the Editor) listing those
files to be put into the library an separate lines.  You can add files to an
existing library or a new one.	The library must have been created before
running BUILDLIB.  If you have a series of files to add to a library that are
not yet converted into Spectra Calc .SPC files, put all the files in one
directory (separate from your other data) and run CONVERT, then run BUILDLIB.
BUILDLIB automatically assumes the files are .SPC files.  If the files listed in
the directory or the ASCII text file are not .SPC files they will not be added
to the library.

CONVERT has been improved with an option to import selected files from a list by
using the cursor keys to mark the ones desired.  It accepts a filespec so you
can specify only certain files be displayed.  If no extension is specified, the
default extension for the current converter is used.  You can use wildcards in
the filename but not in the extension.	The space bar marks a file for
import, the '+' key on the numeric keypad marks a file and moves the cursor down
by one.  Press 'Enter' to import the marked files.  If an SPC file already
exists with the name of the file to be import, the new file is not imported.

CURVEFIT has been improved in a variety of ways.  First, it is directly
available from the Arithmetic Other menu.  It now shows the areas of the fitted
peaks and can use peaks which are arbitrary mixtures of Gaussian and Lorentzian
shapes.  Also, Log-Normal band shapes are now available for fitting asymmetric
chromatography peaks with tails.  The latest version can do automatic
straight-line baseline correction as it fits the curves.  It shows the
"remainder" spectrum as you make initial peak guesses by subtracting your
initial peaks from the file.  This allows you to evaluate how well your initial
guesses fit the data.  Also, you may now edit your initial guesses without
restarting the program.  However, the manual's description of CURVEFIT is still
valid in most respects.

When making CURVEFIT peak estimates, simply press the Esc key to redo the
previous peak.	After all peaks have been estimated, "Redo any peak's guess?"
appears.  Answer Yes and then enter a peak number to change any of the peaks.
When changing a peak, the old peak appears.  Simply press Enter to retain it.
To change its position or height, leaving its existing width, move the cursor
and press Enter without pressing F9 or F10 to set the edges.  When asked for
the "Maximum Number of Passes?", you may enter 0 to report only your initial
peak guesses without doing any automatic fit optimization.

If you choose "Select (mixture)" as the peak type, you can individually select
Gaussian, Lorentzian, Log-Normal or Mixture shapes for each peak.  When you
select Mixture, you are asked for the Lorentzian percentage.  Enter 99 for an
almost pure Lorentzian shape, or 1 for an almost pure Gaussian shape, or any
percentage in between.	When using peak table files, the "%L/Rho" column
indicates the amount of Lorentzian in Gaussain/Lorentzian mixture peaks.  For
Log-Normal peaks, it indicates the amount of asymmetry in the peak.  Note that
when making your initial guesses for Log-Normal peaks, you must skew the center
position so that is not exactly in the middle of the peak.  For most
chromatography data, the center should be to the left of the middle.  A
symmetrical guess for a Log-Normal peak may causes an error.

The "Redo any peak's guess?" question also appears when your initial peak
positions are taken from a peak table file.  You are allowed to edit any or
all of the initial peak shapes and positions as described above.  You are also
allowed to save the initial peaks back to a disk file.	You may add 10 to any
Gaussian/Lorentzian number in your initial peak table (column five) to allow
for a negative peak or may add 20 to fix a negative height for a peak.

As CURVEFIT iterates to optimize the fit, you may press the Esc key to stop
after the current pass finishes.  The final menu appears without additional
passes.  In displayed and printed reports and in the peak tables, a sixth
column shows the area of each peak in terms of the curve's X*Y units.

EXPNIC exports an arbitrary spectrum to Nicolet's .NIC file format.  The
Nicolet file converter must be installed first.  This program converts the
chosen file to a the format required by the converter and then exports it.
Unlike the File Export converter, it does not insist that the file run from
0 to 7899 cm-1 with a power of two points.

GVIEW is a new Application which allows a global view, including display
limits, plotting template, and current memory spectra, to be saved and then
later restored to the same state.  You choose a global view name.  A new
<name>.PRM parameter template is saved or restored.  In addition a <name>.GVW
file is used to remember the memory spectra names.  GVIEW allows you to save
the entire display state, including the spectra with which you are working
and then bring back the same data files and parameters at a later time.

INTEGRAT (available from Functions in the Arithmetic Other menu) has been
updated to allow single-band integration without baseline correction.  Also,
it now does trapezoid-rule integration and so results may differ slightly
from previous versions.

INTERPOL now uses a fast 4-point spline algorithm to add new data points
between existing points without altering the existing points and without
FFT-induced ringing distortions.  Interpolated files plot more smoothly
and integrate more reliably.

MENU-NMR is a new Arithmetic menu designed for NMR users.  It has access to many
functions commonly used by NMR spectroscopist.	Some of these include: frequency
to PPM, PPM to frequency, FFT and phasing for complex FIDs, apodization filters,
baseline corrected integral lines, baseline removal, smoothing, curve fitting,
and others.  This menu can be used by copying MENU-NMR.AB into MENU.AB (in DOS)
BEFORE starting Lab/Spectra Calc.

NMR-ADJ has been modified to allow easier switching between PPM and frequency
(Hz).  The application asks for a reference peak and its chemical shift.  The
rest of the spectrum will be re-scaled in PPM based on information imported from
the original NMR data file.  Using NMR-ADJ on a spectrum that is already in PPM
will ask if you want to choose a new reference peak or scale back to frequency.

NMR-FFT is a new Application which computes and phase-corrects an NMR spectrum
from a complex FID imported with one of the Galactic NMR data file converters.
It automatically assumes the phasing information from the last time it was used.
You may then adjust the phase on bands at either end of the spectrum using the
plus and minus keys, the left and right cursor keys (<- & ->), or a mouse.  The
baseline can be expanded during phasing to fine tune the phase.  When both ends
are properly phased, the corrected spectrum can be optionally saved to disk.

NMR-FILT is a new Application that performs many different apodization filters
on complex FIDs imported with Galactic NMR data file converters.  These include
Sine bell, Cosine, Matched exponential, Gauss, Lorentz-Gauss, Optimal
Resolution, Trapezoidal, and zero filling.  Once an initial value is entered,
the filter parameters can be altered with the + & - keys, the <- & -> cursor
keys, or a mouse.  Both the filter and the FID are displayed on the screen.  The
filtered FID can be saved or computed into a spectrum and phased.

NMR-INTG is a new Application that will calculate and display baseline corrected
integral lines for multiple selected regions in an NMR spectrum. These integrals
are saved in memory and can be saved to disk or plotted along with the spectrum.

NMR-PKS is a new Application that will calculate peak areas and save them into a
disk peak table (*.PKS) with the same base name as the current spectrum.  For
Spectra Calc this is the same as the PKS-AREA application.  For Lab Calc this
application creates a peak table according to the currently set parameters.  You
can optionally choose to scale the peak areas to # of nuclei, and write the
results into the "Quan" column of the Lab Calc peak table.

POLYFIT (available from Baseline on the Arithmetic Other menu) has been
updated to allow more points to be specified than the chosen polynomial order.
It can also force all fitted points to fall on the data trace as an option.

PRINTSPC is a new application which allows you to select a series of spectra to
plot with the current template in a batch mode.  This allows you to set up a
series of plots and leave.  As shipped, it requires the DOS program SORT.EXE or
SORT.COM be available in your path so it can present a sorted directory of SPC
files to select from.  If you do not have SORT available, change the line in
the beginning of the application "S = 1" to "S = 0" to disable sorting.  It is
normally configured to plot to the graphics printer.  If you have a plotter with a page feeder, you can change the line "P = 0" to "P = 1" to enable printing
to the plotter instead.  You can specify a wildcard filespec to have only
certain SPC files presented in the file selector.  For example "pol*" to show
only files beginning with "pol" and ending in anything.

The REPORT application prints X and Y values as numbers on the graphics printer
currently set in the Plot menu.  It either reports on the current trace in
memory or allows you to choose a single trace file from the disk.  REPORT
allows you to restrict the printed values to any specified X range and allows
the X axis interval between reported values to be specified.  It automatically
includes introductory text line(s) from a special ADDRESS.TXT ascii text file
(if one exists in the current default directory) at the top of the report.  It
also automatically reports the trace's file name and comment line.

SHIFT (selected from the Arithmetic/Other menu) has been enhanced to allow
shifts with one end point anchored.

SPLICE is a new Application which allows files to be "patched" together as a
single spectrum.  Data can be measured over different spectral regions, with
different resolutions and even from different instruments.  SPLICE expects the
files all to have the same name except for sequentially numbered last
characters.  For example, if you had three spectra to splice together, use the
DOS rename command to name them something like SPEC1.SPC, SPEC2.SPC and
SPEC3.SPC.  When you run SPLICE, select the first sequentially numbered
spectrum (SPEC1.SPC in the example) and all the spectra will be "patched"
together into a single spectrum file.

SSP is a new program to do standard spectral plots (with two times scale
expansion below 2000 cm-1).  Uses the SSP.PRM template to set up limits for
the plot.  Load an IR spectrum (either transmission or absorbance) into memory
and choose SSP from Arithmetic DoProgram.  You will see the SSP plot on the
screen and are asked whether it should be plotted or printed.

XYIMPORT reads in ASCII XY values from a file and linearizes the XY pairs to
equally spaced X intervals.  It creates a normal .SPC spectrum file.  The
input file is an ASCII text file with an assumed .PRN filename extension.
It must have a separate X,Y coordinate pair on each line and the X values must
be in ascending order.	The file is read into memory and linearized using the
Array Basic XADJUST statement.	XYIMPORT works best on data whose X intervals
do not change radically across the spectrum.

ZAP now includes an option to add a Lorentzian to a spectrum.

ARRAY BASIC

"PORTOUT -30,tabsize" allows the PRINT and LPRINT tab spacing to be reset to
a value other than the default of 16 columns per tab.

You may now use OPENSPC to access spectra whose filenames begin with numerals
as long as you follow the filename with a correct variable name beginning
with a letter:	OPENSPC "123",spc

Variable names (other than #S, #R, #1, #2, etc.) no longer refer to matching
names of spectra that have been retrieved into memory.	This means that
Array Basic programs using names like i, j, etc. for scalar variables work
even when similarly-named spectra happen to be loaded into memory.  However,
spectra may be referenced by name if recently created with NEWSPC.  The
"PORTOUT -28,value" statement turns spectrum name matching on or off given
1 or 0 as the value.  When on, an Array Basic variable can refer to an
in-memory spectrum by the same name.

Also, "PORTOUT -27,value" allows the error beep to be turned off (value=0) or
on (1) from Array Basic.  "PORTIN -27,variable" returns a non-zero value if a
"PRESS ANY KEY..." error has occurred since its last use.  "PORTOUT -26,value"
turns matrix/range printing off (value=0) or on (1).  "PORTIN -31,variable"
gets the maximum number of text lines on the screen.   Using "PRINTLINE 1"
always places text 25 lines above the bottom of the screen.  However, for
large screens with more than 25 lines, you may use negative numbers with
PRINTLINE to write to the top of the screen.  Finally, PORTIN and PORTOUT may
be used with port numbers between -120 and -132 to read and write the date,
time, and resolution characters from the current #S memory spectrum.  Use -120
for the year, -121 for the month, -122 for the day, -123 for the hour, -124
for the minute, and -125 through -132 for the eight resolution characters.

PORTOUT -160,value  ...  PORTOUT -179,value
PORTIN -160,variable  ...  PORTIN -179,variable
The PORTIN and PORTOUT statements have been extended to allow up to twenty
additional values to be accessed in the file header for the current #S spectrum
in memory.  Port numbers -160 through -179 address the twenty possible values.
These values are loaded and saved from normally-unused locations at the end
of the spectrum file's comment area.  Comments beyond the first 80 bytes used
in the memo line are shared with these locations and conflicts are possible if
you also use STRING string,-86 statement.

PRINTLINE line [,column]
PRINTLINE has been extended to allow a column number to be specified after the
line.  Column 1 is the left most character.  If the column is included, then
the next PRINT to the screen begins as specified and, moreover, writes over
only a portion of the screen.  Screen areas before and after the specified
print characters are left unchanged.  Thus "PRINTLINE row,column" allows
writing to spcific places on the screen.  However, later PRINT's revert to the
normal whole-line mode unless the next PRINT ends with a semicolon (;) or
unless another PRINTLINE with a column is executed.

READ #file, $scalar
WRITE #file, $scalar
The READ and WRITE statements have been extended to allow a single byte value
to be read from or written to a disk file.  If a "string" or $array appears
instead of a scalar, only the first character is used.	Unlike INPUT #file
and PRINT #file, the READ and WRITE statements can be used with zero values.

The SEEK statement returns the destination byte offset from the beginning of
the file in the variable named "V".  Thus, "SEEK #1, -0" seeks to the end of
the file and sets V to the number of bytes in the file.

New command codes are available for STRING.  "STRING $variable,-15" gets the X
axis label override text and "STRING string,-16" sets the X axis label text.
Similarly, -17 and -18 get and set the Y axis label override text.  These are
the same labels which may be set from the Environment Axes labels menus.  For
the standard labels tied to the current spectrum to appear, the first bytes of
these override text labels must be zero.  "STRING $variable,-19" sets the
$variable string to the text version of the number currently in the scalar
variable named "V".  "STRING string,-20" sets the value of the scalar variable
named "V" to the number represented by the string.  Thus, -19 and -20 allow
you to convert a number to text and a text to a number.

FONTS

A new GREEK font has been added.  It includes various Greek letters and
other special symbols, mapped to the normal roman character set.  When this
font is chosen in Draw, the mapped special symbols appear in the drawing
when you type the corresponding roman characters on the text lines.

PRINT/PLOT DRIVERS

Print drivers have been added for the Hewlett Packard DeskJet printer.
When installing Spectra Calc, choose DESKJET3 for the 300 dots-per-inch
full-resolution version, or DESKJET1 for the faster 150 dpi version.  The
DESKJET3 version requires a hard disk.	If you hear a beep when plotting to
the printer, you should switch to the DESKJET1 version.

Also, the Paint Jet color printer is now supported.  Choose HPPJ_180 for 180
dots per inch plots or HPPJ_90 for 90 dpi.  Note that these drivers do not
support yellow.  Yellows appear as black.  Also, orange is only supported at
90 dpi and prints as red at 180 dpi.

New drivers for Epson and compatible 24 Pin printers have been added for both
landscape (EPSON24) and portrait (EPSON24P) modes.  These drivers produce high
quality plots at 180 by 180 DPI resolution on 24 pin Epson printers and
compatibles such as the Panasonic KX-P1124.

IMPORT/EXPORT FILE CONVERTERS

ASCII_XY
The import assumes that the X,Y pairs are equally spaced on the X axis.
Therefore, it uses only the first and last X values.  All other X coordinates
are ignored and equally spaced X values are used instead.  Note that the Array
Basic XADJUST statement can be used to interpolate X,Y pairs taken from two
separate spectra or arrays into a single spectrum.

BOMEM_DA
Works with Bomem DA3 or DA8 binary floating-point files transfered unmodified
from the DEC computer.	It looks for files ending with *.DA filename extensions.

DILOR_1
DILOR_2
Dilor 1 is for the old Version 1 Dilor Microdil 28 format.  Dilor 2 is the
newer format.  Both look for *.DLR Ascii text files.  The Dilor converters
create two additional binary-format files when the import file is a Dilor
Multichannel spectrum.	These two files have the same name as the Galactic
data file with extensions of '.X' and '.Y.'  These two files are used by the
XYADJUST Arithmetic Application program to correct the Galactic data file for
the non-linear X spacing of the Multichannel data.  To adjust a Multichannel
Dilor file after importing it, File Retrieve it to make it the current
spectrum and select "Arithmetic DoProgram" and type "XYADJUST".  Then press
Enter.	You must save the correct spectrum to disk if you want to replace the
original data.

G_WAVE
Looks for Guided Wave *.GW Ascii text files.

HP_8452K
Works with *.TIM Kinetics files from the Hewlett Packard 8452.	Works only
with FTYPE=14 kinetic-type files.  (See the HP-8452 converter for for
wavelength-type files.)

HORIBA
Works with Sanyo Horiba FT300 IEEE format files.  Looks for *.HSP extensions.
The HORIBA.AB Arithmetic Application displays special FT300 parameters.

ISA_RAMN
Works with ISA Raman Spectrophotometer binary format files.  Looks for files
with *.L00 extensions.	Handles *.S00, *.M00, *.T00 and *.D00 files also, but
extensions must be typed along with the ISA file name.	Alternatively, you may
rename files to use *.L00 extensions so that they appear on the Import menu.

LTI
Works with LTI SpectraMetrix multi-spectra data.  It looks for files ending
with *.DAT filename extensions for spectral data and files ending with *.ING
for sample names and comments.	This converter currently works only with
absorbance data.  The EXPLTI.AB Arithmetic Applicaiton may be used to export
to LTI format files when the data was not imported with the LTI converter.

MATTSON
Mattson data files consist of a group of data files all with the same filename
but with different extensions.	There is always a ASCII text file with a *.HDR
extension as well as one or more data files with various extensions as shown
below.	The *.HDR file must be present for Spectra Calc to convert the data.
In addition more than one data file may be present if you wish to convert
several files.	This converter will convert any data files it finds with the
same name as the *.HDR file you choose in the File/Import command.  The
converter adds a single letter to the end of the filename (or replaces the last
letter if already 8 characters long) as follows:

   Mattson Name  SC Name	File Contents
   FILENAME.HDR  none		Header file, must be present
   FILENAME.ABS  FILENAMA.SPC	Absorbance spectrum
   FILENAME.RAS  FILENAMT.SPC	Transmittance (or reflectance) spectrum
   FILENAME.DTR  FILENAMD.SPC	Diffuse reflectance spectrum
   FILENAME.SBM  FILENAMS.SPC	Sample single beam spectrum
   FILENAME.BKG  FILENAMB.SPC	Background single beam spectrum
   FILENAME.IGM  FILENAMI.SPC	Sample interferogram
   FILENAME.BIG  FILENAMG.SPC	Background interferogram

Because this converter writes to a different filename than the *.HDR file, you
will not be warned if a file with the same name already exists!  Make sure you
do not convert two Mattson files with the same *.HDR filename unless you do not
want to save the first set of data.

The Mattson UNIX system normally adds a carriage return to every line feed in
a text file when they send it to the screen or another computer.  YOU MUST
TRANSFER ALL DATA FILE IN "RAW" MODE (not the default text mode) or the data
will be unusable.  The Mattson data files are 8-bit binary data files.	You
must transfer all 8 bits of every byte or the converter give a "Not a valid
Mattson data file." error.  Make sure both the communication parameters are set
to 8 data bits on both computers and use a file transfer program on the UNIX
system with does not strip the high bit from each byte.

PE_7000
Looks for *.SP binary-format files from the Perkin-Elmer 7000 data station
byte-reversed integers.  You should normally use this converter in place of
the PERKIN-E converter for binary data.  Try both if you have problems.

PESAM
Converter for the Perkin Elmer Scanning Auger Microscope with PC 137 board.
The PESAM converter imports raw *.bin binary Survey data written to an
IBM-PC by the PC 137 optional board and software.  This is an import
only converter.

SPCTRA_P
Works with Spectra Physics Chromstation binary data.  It looks for Spectra
Physics files ending with *.RAW filename extensions.

SPEX
Works with SPEX Raman IEEE binary data.  It looks for SPEX files ending with
*.SPT filename extensions.

TELOS
This converter looks for a *.MSR filename extension.  It should properly
convert *.REF files when you type both the name and .REF extension at the
'Enter Telos data file name:' prompt.  Optionally, you may want to rename
any files with these extensions to *.MSR To export spectra to Telos format,
they must have X units set to wavenumbers, 4096 points, the first point at 0
cm-1, and the last point at 7899.46 cm-1.  However, the TELOS.AB Arithmetic
Application can be used to export the current spectrum to a Telos data file.
Select Arithmetic DoProgram and enter TELOS.  The current spectrum is exported
to the disk as a Telos format file with the same name but a *.MSR extension.

TRACOR
Reads diode array data files created by the Tracor Northern TN-6600.  It looks
for files ending with *.SP filename extensions.  It should properly convert
*.HI, *.RF and other data files if you type both the filename and the
extension at the 'Enter Tracor data file name:' prompt.  Optionally, you may
want to rename files with these extensions to *.SP.  This converter can export
spectra of up to 8192 points.  The export spectrum cannot have X units of
wavenumbers.  If you wish to export a spectrum with units of wavenumbers,
first run the NMETER Arithmetic Application to convert it to nanometers and
save it to disk with a new name before exporting.

VARIAN_C
The Varian converter has been updated to provide more support for reflectance
and absorbance conversion from the DS-15 station.  The VARIAN_C converter MUST
be driven by the Array Basic program VARIAN_C.AB for both import and export.
Start your import or export by first going to the Arithmetic menu then choosing
DoProgram VARIAN_C.  You should not use Import or Export from the File menu.

VAR_NMR  (File converter for Varian - Silber NMR data)
Steven Silber at Texas A&M has written a package to convert Varian NMR binary
data into the IBM-PC format.  The Varian file converter works only with the
Silber preprocessed data files and will not read Varian data directly.	The
Silber package is available from:

		Steven Silber
		Dept. of Chemistry
		Texas A&M University
		College Station, Texas	77843-3255
		(409) 845-1745

Before you start Spectra Calc, create a subdirectory for each conversion of
interest.  This is required required because the same file names for the Varian
data are used for each conversion.  Then load TEXT.TXT, ACQPAR., and FIDFIL.
(if a FID) or TEXT.TXT, ACQPAR., PRCPAR., and PHASFL. (if a spectrum).	The
absence of FIDFIL.  flags a spectrum file.  Therefore, if a FIDFIL. is found
the spectrum in PHASFL. is ignored.

To convert a Varian - Silber FID or Spectrum file:
1) Make sure you are in the correct subdirectory using F2/Environment/Directory.
2) Use F2/File/Import and choose the only selection: "TEXT".  Then for the
   output, give the FULL PATH and NEW file name, ("\SC\DATA\MYFILE" for
   example) to write the converted data into a common directory.

WATERS
Reads Waters Maxima 820 Raw Chromatogram Format.  Looks for files with a .DAT
extension.  The Waters Maxima file converter imports and exports the raw
A/D 24 bit signed binary data versus time in minutes.  The data is imported
such that the maximum possible 22 bit A/D value scales to unity.


